TECHNICAL ISO/TS SPECIFICATION 13399-308 Firstedition 2016-02-01 Cutting tool data representation and exchange - Part 308: Creation and exchange of 3D models Milling cutters with arbor hole for indexable inserts Représentation et échange des données relatives aux outils coupants - Partie 308: Création et échange des modeles 3D - Fraises a meétaux a trou de fixation et a plaquettes amovibles Reference number IS0/TS13399-308:2016(E) TSO International Organization for Standardization @ IS0 2016 I without license from IHS IS0/TS 13399-308:2016(E) COPYRIGHTPROTECTEDDOCUMENT IS02016,PublishedinSwitzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester. ISO copyrightoffice Ch. de Blandonnet 8 . CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 [email protected] www.iso.org Intenationaibr PrganizationforStandardization ensee-ZHEJIANG INST OF STANDARDIZRoISQ ,6 - All rights reserved Not for Resale, 2016/4/22 08:01:01 etworking permitted without license from IHS IS0/TS 13399-308:2016(E) Contents Page Foreword ..V Introduction. ..vii 1 Scope. 2 Normative references 3 Starting elements, coordinate systems, planes .2 3.1 General. 3.2 Reference system .2 3.3 Coordinate system at the cutting part 3.4 Planes .3 3.5 Design of the pocket seat and cutting reference point (CRP) of the insert 4 3.6 Adjustment coordinate system on workpiece side .7 3.6.1 General .7 3.6.2 Designation of the coordinate system workpiece side .8 4 Design of the model .9 4.1 General .9 4.2 Necessary parameters for the connection interface feature. .10 4.3 Necessary properties for inserts 10 4.3.1 General. 10 4.3.2 Properties for equilateral, equiangular and equilateral, nonequiangular inserts 10 4.3.3 Properties for nonequilateral, equiangular and nonequilateral, noneguiangularinserts .11 4.3.4 Design of the pocket seat feature ..12 5 Face milling cutter .12 5.1 General. ..12 5.2 Necessary properties. ..13 5.3 Basic geometry. ..13 5.4 Determination of the position of the mounting coordinate system of insert .14 5.5 Chip flute and pocket seat .15 5.6 Face milling cutter, assembly .16 6 Shoulder milling cutter .17 6.1 General .17 6.2 Necessary properties. .17 6.3 Basic geometry .17 6.4 Determination of the position of the mounting coordinate system of insert ..17 6.5 Chip flute and pocket seat .18 6.6 Shoulder milling cutter, assembly .18 Plain milling cutter .19 7.1 General. .19 7.2 Necessary properties. .19 7.3 Basic geometry .20 7.4 Determination of the position of the mounting coordinate system of insert .20 7.5 Chip flute and pocket seat 21 7.6 Plain milling cutter, assembly .23 8 Shell milling cutter .23 8.1 General. 23 8.2 Necessary properties 24 8.3 Basic geometry 24 8.4 Determination of the position of the mounting coordinate system of insert .25 8.5 Chip flute and pocket seat 25 8.6 Shell milling cutter, assembly .25 9 Full-side-slot milling cutter .25 iii ZHEJIANG INST OF STANDARDIZATION C1 5956617 vided by IHS under license with ISt ed without license from IHS