ISO/TS TECHNICAL SPECIFICATION 13399-303 First edition 2016-02-01 Cutting tool data representation and exchange - Part 303: Creation and exchange of 3D models Solid end mills Representation et échange des données relatives aux outils coupants - Partie 303: Creation et échange de modeles 3D - Fraises cylindriques deux tailles monobloc Reference number IS0/TS13399-303:2016(E) ISO International Organization for Standardization @ IS0 2016 ZHEJIANG INST OF STANDARDIZATION C1 5956617 ted without license from IHS IS0/TS 13399-303:2016(E) COPYRIGHTPROTECTEDDOCUMENT IS0 2016, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 . CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 [email protected] www.iso.org Internationai ibr DrganizationforStandardization icensee-ZHEJIANG INSTOF STANDARDIZAoIS 06 - All rights reserved Not for Resale, 2016/4/22 08:00:26 networking permited without license from IHS IS0/TS 13399-303:2016(E) Contents Page Foreword ..V Introduction. ..vii 1 Scope. 2 Normative references 3 Starting elements, coordinate systems, planes ..2 3.1 General. 2 3.2 Reference system.. 3.3 Coordinate system at the cutting part .3 3.4 Planes 3.5 Cutting reference point (CRP) .4 4 Design of the model .5 4.1 General ..5 4.2 Necessary parameters for the connection interface feature ..5 5 Non-centre cutting end mill .5 5.1 General. 5.2 Necessary properties. .6 5.3 Geometry of the non-cutting part inclusive of the connection. .7 5.4 Geometry of the cutting part. ..7 5.5 Complete non-centre cutting end mill .8 6 Centre cutting end mill .9 6.1 General .9 6.2 Necessary properties. ..9 6.3 Geometry of the non-cutting part inclusive of the connection. 6.4 Geometry of the cutting part ..10 6.5 Complete centre cutting end mill ..10 7 Angular end mill (V-groove) ..11 7.1 General ..11 7.2 Necessary properties. .11 7.3 Geometry of the non-cutting part inclusive of the connection. ..11 7.4 Geometry of the cutting part. .. 12 7.5 V-groove end mill, complete. ..13 8 Dovetail end mill. ..13 8.1 General. ..13 8.2 Necessary properties. ..13 8.3 Geometry of the non-cutting part inclusive of the connection .13 8.4 Geometry of the cutting part. ..14 8.5 Complete dovetail end mill, complete .15 9 T-slot end mill. ..15 9.1 General. .. 15 9.2 Necessary properties. ..15 9.3 Geometry of the non-cutting part inclusive of the connection ..15 9.4 Geometry of the cutting part. ..16 9.5 Complete T-slot end mill. .16 10 Ball-nosed end mill ..17 10.1 General. .17 10.2 Necessary properties ..17 10.3 Geometry of the non-cutting part inclusive of the connection. ..18 10.4 Geometry of the cutting part .18 10.5 Complete ball-nosed end mill. ..18 11 Die end mill ..19 ii Censee=ZHEJIANG INST OF STANDARDIZATION C1 5956617 ed without license from IHS Not for Resale, 2016/4/22 08:00:26