ISO INTERNATIONAL STANDARD 16369 Second edition 2007-10-15 Elevating work platforms - Mast-climbing work platforms Plates-formes élévatrices de personnel- Plate-formes se deplacant le long de mat(s) Reference number ISO 16369:2007(E) @ ISO 2007 oyIHSunder itted without license from IHS Not for Resale ISO 16369:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHTPROTECTED DOCUMENT @ISO2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either isO at the address below or IsO's memberbody in the country of the requester. ISO copyright office Case postale 56. CH-1211Geneva 20 Tel. + 4122 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ ISo 2007 - All rights reserved I without license from IHS Not for Resale ISO 16369:2007(E) Contents Page Foreword Introduction 1 Scope 2 Normative references 3 Terms and definitions. 3 4 List of hazards.. 5 Safety requirements and/or measures 10 5.1 Structural and stability calculations ... 10 5.2 General requirements for machine, base frame, chassis and mast. 18 5.3 Work platform.... 22 5.4 Drivesystemsforelevation. 24 5.5 Means to prevent the work platform from falling with overspeed 29 5.6 Means for emergency lowering and raising the work platform .. 31 5.7 Overload/moment device ... 32 5.8 Electrical systems.. 33 5.9 Drive systems powered by internal combustion engine.... 34 5.10 Hydraulic system ..... 35 5.11 Specialrequirementsforsafetydevicesdependingonauxiliarycircuits,andfor overload/moment detection devices.. .36 5.12 Travel limit switches........ 36 5.13 Controls, 6 Verification of safety requirements and/or measures for each new model of McwP .... 37 6.1 Design check.... .37 6.2 Practical tests... 37 7 Information to be provided .. 39 7.1 Instruction handbook. 39 7.2 .46 Annex A (informative) Structural calculations... Annex B (normative) Special requirements for multilevel work platforms...... Annex C (normative) Requirements for electrical and electronic aspects for overload-detection devices.... .65 Bibliography .68 Copyright International Organizaion for Standardizalon ghts reserved ii from IHS Not for Resale ISO 16369:2007(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (isO member bodies). The work of preparing International Standards is normally carried out through isO technical committees. Each member body interested in a subject for which a technical committee has been International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2 The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent r