ISO INTERNATIONAL STANDARD 16100-2 First edition 2003-11-01 Industrial automation systems and integration Manufacturing software capability profiling for interoperability Part 2: Profiling methodology Systemes d'automatisation industrielle et integration Profil d'aptitude du logiciel de fabrication pour interopérabilite- Partie 2: Methodologie d'eélaboration de profils Reference number X ISO 16100-2:2003(E) ISO @ ISO 2003 ISO 16100-2:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the respons bility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, IsO'smemberbody in the country of the requester. ISO copyright office Case postale 56 : CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ii @IsO2003-Allrightsreserved ISO 16100-2:2003(E) Contents Foreword IV Introduction 1 Scope. 2 Normative references 3 Terms and definitions. 4 Abbreviated terms. 5 Capability profiling method.. 5.1 Capability profiling concept. 5.2 Capability profiling process. 5.3Software requirements analysis process. 5.4Software unit selection and verification, or creation process 6 Elements and rules for capability profiling 6.1 Taxonomy. 6.2 Capability classes and their content. .6 6.3 Capability templates and rules 1 6.4 Capability profiles and rules 12 6.5 Software unit profile database 13 6.6Rules for matching capability profiles .. .13 6.7 Interoperability criteria .... 13 7 Conformance. .13 Annex A (informative) Reference methods 14 A.1 Extensible Markup Language (XML). ...14 A.2 Vocabularies, definitions and interchange formats for software packages: Open Software Description (OSD) and Channel Definition Format (CDF) A.3 Distributing software services: Open Distributed Processing (ODP) and Common Object Request Broker Architecture (CORBA). .15 Bibliography.. .17 IsoO2003—Allrightsreserved ili ISO 16100-2:2003(E) Foreword (isO member bodies). The work of preparing International Standards is normally carried out through IsO technicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnical committeehasbeer non-governmental, in liaison with IsO, also take part in the work. IsO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. InternationalStandardsaredraftedinaccordancewiththerulesgivenintheISO/lECDirectives,Part2 The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 16100-2 was prepared by Technical Committee ISO/TC 184, Industrial automation systems and integration, Subcommittee Sc 5, Architecture, communications and integration fr