ISO INTERNATIONAL STANDARD 15736 First edition 2006-01-15 Ships and marine technology Pyrotechnic life-saving appliances Testing, inspection and marking of production units Navires et technologie maritime Appareils pyrotechniques de sauvetageEssais,controleetmarquagedesunitesdeproduction Reference number ISO 15736:2006(E) @ ISO 2006 No r py IHS under itted without license from IHS Not for Resale ISO15736:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF fle can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ?ISO2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, IsO's member body in the country of the requester. ISO copyright office Case postale 56. CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ ISO 2006 - All rights reserved ermittedwithoutlicense from IHS Not for Resale ISO 15736:2006(E) Contents Page Foreword. Introduction 1 Scope 2 Normative reference(s)... 3 Term(s) and definition(s).. 4 General requirements.. 4.1 Manufacturing standards .. 4.2 Visual appearance and craftsmanship 4.3 Markings ....... 4.4 Documentation. 5 Performancerequirements 5.1 Rocket parachute flare . 5.2 Hand flare ........ 5.3 Buoyant smoke signal 5.4 Lifebuoy self-activating smoke signal... 5.5 Line-throwing appliances .... 6 Test procedures 6.1 Luminous intensity measurement 6.2 Thrustversustimemeasurement 6.3 Altitude measurement, 6.4 Temperature cycle test. 6.5 Water immersion test 6.6 Cold temperature test.. 6.7 Hot temperature test... 6.8 Smoke density measurement. 6.9 Smoke colour comparison. 6.10 Burn time measurement... 6.11 Line throwing appliance function test.. Annex A (informative) Production testing and inspection procedures ... Copyright Interational organizainrsadardizalionghts reserved ii Not for Resale ISO 15736:2006(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (IsO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with isO, also take part in the work. iso collaborates closely with the International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 15736 was prepared by Technical Committee ISO/TC 8, Ships and marine technology, Subcommittee SC 1, Lifesaving and fire protection. @ ISo 2006 - All rights reserved ional Organization for Standardizatior ISO 15736:2006(E) Introduction This International Standard is i