ISO INTERNATIONAL STANDARD 15616-2 First edition 2003-03-01 Acceptance tests for O2-laser beam machines for high quality welding and cutting Part 2: Measurement of static and dynamic accuracy Essais de réception des machines de soudage et de coupage de qualité par faisceau laser CO2 Partie 2: Mesure de la precision du systeme de mise en ceuvre du faisceau en statiqueet endynamique Reference number ISO 15616-2:2003(E) ISo @ ISO 2003 Copyright International Organization for Standardization ted without license from IHS Not for Resale ISO 15616-2:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below @ISO2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic in the country of the requester. ISO copyright office Case postale 56 . CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland Copyightinteratinal organization for Standardization @ ISo 2003 - All rights reserved mitted without license from IHS Not for Resale ISO 15616-2:2003(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (IsO committees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeenestablishedhas the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with sO, also take part in the work. IsO collaborates closely with the International Electrotechnical Commission(lEC)onallmattersofelectrotechnicalstandardization International Standards are drafted in accordance with the rules given in the ISO/lEc Directives, Part 3 The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 15616-2 was prepared by the European Committee for Standardization (CEN) in collaboration with Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 10, Unification of requirements in the Agreement). Throughout the text of this document, read "...this European Standard.." to mean "...this International Standard...". IsO 15616 consists of the following parts, under the general title Acceptance tests for CO2-laser beam machines for high quality welding and cutting: 一 Part 1: General principles, acceptance conditions Part 2: Measurement of static and dynamic accuracy Part3:Calibration of instrumentsformeasurementofgasflowandpressure ii Not for Resale ISO 15616-2:2003(E) Contents page Foreword .v 1 Scope 2 Normative references 3 Terms and definitions. 4 Examination of the manipulation system precision. 2 4.1 Extent of examination... 4.2 Measuring devices. 2 4.3 Examination procedure 4.4 Report of the measurement results.. 10 5 Examination of the trajectory exactness... 5.1 Extentof examination. 5.2 Definitionofgeometricalelementsandexactnessdescribingcharacteristics 10 5.3 Measuring devices ... 5.4 Examination procedure .. 5.5 Test wor