ISO INTERNATIONAL STANDARD 15600 First edition 2000-05-01 Tools for moulding Thermal insulating sheets for injection moulds Outillage de moulage - Feuilles d'isolation thermique dans les moules d'injection Reference number ISO15600:2000(E) tso @ ISO 2000 No reproduction or networking permited without license from IHS Not for Resale ISO 15600:2000(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The IsO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. @ISO2000 tronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's mem- ber body in the country of the requester. ISO copyright office Case postale 56 · CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 734 10 79 E-mail [email protected] Web www.iso.ch Printed in Switzerland pyhatoganizatSandadizatio @ ISO 2000 - All rights reserved No reproduction or networking permitted without license from IHS Not for Resale ISO15600:2000(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (IsO member bodies). The work of preparing International Standards is normally carried out through IsO technical com- mittees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeenestablishedhasthe son with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (lEC) on allmatters ofelectrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. patent rights. IsO shall not be held responsible for identifying any or all such patent rights. SC 8, Tools for pressing and moulding. CopyrightInternationalOrganizationforStandardizationserved ii Not for Resale Copyriahtlntematina Organizatin r Standardizatin Nrroductioneworkingemitedwithout licenefrm Not for Resale ISO 15600:2000(E) INTERNATIONAL STANDARD Tools for moulding Thermal insulating sheets for injection moulds 1 Scope This International Standard lays down the basic dimensions and tolerances, in millimetres, of type A and B thermal insulating sheets for plastic and rubber moulds. Thermal insulating sheets are used in applications where heat trans- material guidelines and design requirements, and specifies the designation of the insulating sheets. eter ( 90 mm) of locating rings. Type A Type B Figure 1 - Example of mounting of thermal insulation sheets Dimensions See Figures 2 and 3 and Table 1. to the manufacturer's discretion. No reproduction or networking permited without license from IHS Not for Resale ISO 15600:2000(E) Dimensions in millimetres 0.05/100 Figure 2 Type A thermal insulating sheet Dimensions in millimetres Φ 0,2 0,05/100 5.5 Figure 3 Type B thermal insulating sheet @IsO2000-All rights reserved No reproduction or networking permited without license from IHS Not for Resale ISO 15600:2000(E) Table 1 Dimensions of type A and B thermal insulating sheets Dimensions in millimetres Dimensions Dimensions Dimensions m t m 1 t w 1 t 2.,0 28 2.0 =28 2,5 2,5 96 × 96