ISO INTERNATIONAL STANDARD 15536-2 First edition 2007-03-01 Ergonomics Computer manikins and body templates Part 2: Verification of functions and validation of dimensions for computer manikin systems Ergonomie Mannequins informatisés et gabarits humains - Partie 2: Verification des fonctions et validation des dimensions pour les systemes de mannequins informatisés Reference number ISO 15536-2:2007(E) @ ISO 2007 ISO15536-2:2007(E) PDFdisclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The Iso Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation ISO2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either isO at the address below or IsO's member body in the country of the requester. ISO copyright office Case postale 56 : CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ISO 2007-All rights reserved ISO 15536-2:2007(E) Contents Page Foreword. iv Introductior 1 Scope 2 Normative references 3 Terms and definitions 4 Requirements for computer manikin verification. 4.1 4.2 Listing of functions.. 4.3 Description of functions.. 4.4 Verification of functions - - Examples supplied by developers.... 4.5 Verification of functions - Enabling manikin system user to record/report performance 5 Requirements for documenting source data ... 5.1 Listing of parameters 5.2 Parameterdescription.. 5.3 Sampling method.... 5.4 Sample demographics 6 Requirements for computer manikin validation. 6.1 General requirements ... 6.2 Static functions .... 6.3 Reporting test results Annex A (informative) Recommended nomenclature and definitions of joint movements for modelling humans . Annex B (informative) Static-test protocol . 16 Bibliography. 1> anization for Standa ion'ghts reserved ili ISO 15536-2:2007(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (isO member bodies). The work of preparing International Standards is normally carried out through IsO technical committees. Each member body interested in a subject for which a technical committee has been non-governmental, in liaison with iso, also take part in the work. Iso collaborates closely with the InternationalElectrotechnicalCommission(lEC)onallmattersofelectrotechnicalstandardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2. adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 15536-2 was prepared by Technical Committee ISO/TC 159, Ergonomics, Subcommittee SC 3, Anthropometry and biomechanics. CEN/TC 122, Ergonomics, in collaboration with Technical CommitteeISO/TC 159, Ergonomics, Subcommittee sc 3, Anthropometry and biomechanics, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). Iso 15536 consists of the following parts, under the general title Ergonomics - Computer manikins and body templates: Part