BS IS0 15531-43:2006 BSl Standards Publication Industrial automation systems and integration - Industrial manufacturing management data Part 43: Manufacturing flow management data: Data model for flow monitoring and manufacturing data exchange bsi. BS IS0 15531-43:2006 BRITISH STANDARD National foreword This British Standard is the UK implementation of IS0 15531-43:2006 The UK participation in its preparation was entrusted to Technical Committee AMT/4, Industrial data and manufacturing interfaces. A list of organizations represented on this committee can be obtained on request to its committee manager. Contractual and legal considerations This publication has been prepared in good faith, however no representation, warranty, assurance or undertaking (express or implied) is or will be made, and no responsibility or liability is or will be reasonableness of this publication. All and any such responsibility and liability is expressly disclaimed to the full extent permitted by the law. This publication is provided as is, and is to be used at the recipient's own risk. The recipient is advised to consider seeking professional guidance with respect to its use of this publication. This publication is not intended to constitute a contract. Users are responsible for its correct application. @ The British Standards Institution 2023 Published by BSI Standards Limited 2023 ISBN978053922219 7 ICS 25.040.40 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2023. Amendments/corrigenda issued since publication Date Textaffected BS IS0 15531-43:2006 INTERNATIONAL ISO STANDARD 15531-43 First edition 2006-08-15 Industrial automation systems and integration Industrial manufacturing management data - Part 43: Data model for flow monitoring and manufacturing data exchange Systemes d'automatisation industrielle et integration - Donnees de gestion de fabrication industrielle Partie 43: Donnees de gestion des flux de fabrication: Modele de donnees pour suivi des flux et échange des données de fabrication Reference number IS0 15531-43:2006(E) iso @ IS0 2006 BS IS0 15531-43:2006 IS0 15531-43:2006(E) COPYRIGHT PROTECTED DOCUMENT IS0 2006, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester IsO copyrightoffice Ch. de Blandonnet 8 . CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 [email protected] www.iso.org ii @ IS0 2006 - All rights reserved BS IS0 15531-43:2006 IS0 15531-43:2006 Contents Page Foreword .iv Introduction. .V 1 Scope. ..1 2 Normative references 3 Terms, definitions, and abbreviations .2 3.1 Terms and definitions .2 3.2 Abbreviations... ..6 4 General purpose and scope of Is0 15531 .6 5 Manufacturing flow management data .7 5.1 Management of manufacturing flows. .7 5.2 Fundamental concepts and assumptions. .9 5.3 Manufacturing flow management data schema definition .10 5.4 manufacturing flow management data type definitions. 11 5.4.1 type_of_flow .11 5.4.2 type_of_material_flow .12 5.5 Manufacturing flow management data subtype constraint definitions .12 5.5.1 material_information .12 5.5.2 rawmat_component .12 5.6 Manufacturing flow management dataentity definitions 12 5.6.1 process. .12 5.6.2 flow .13 5.6.3 Process flow assignment 14 5.6.4 process_property_value .14 5.6.5 flow_property_value .14 5.6.6 material_flow ..14 5.6.7 information_flow .15 5.6.8 raw_material .15 5.6.9 component .15 Annex A (normative) Use of ASN.1 Identifiers in SC4 standards .16 Annex B (informative) EXPRESS listing ..17 Anne