BS IS0 15531-42:2005 BSl Standards Publication Industrial automation systems and integration - Industrial manufacturing management data Part 42: Time Model bsi. BS ISO 15531-42:2005 BRITISH STANDARD National foreword This British Standard is the UK implementation of IS0 15531-42:2005. The UK participation in its preparation was entrusted to Technical Committee AMT/4, Industrial data and manufacturing interfaces. A list of organizations represented on this committee can be obtained on request to its committee manager. Contractual and legal considerations This publication has been prepared in good faith, however no representation, warranty, assurance or undertaking (express or implied) is or will be made, and no responsibility or liability is or will be reasonableness of this publication. All and any such responsibility and liability is expressly disclaimed to the full extent permitted by the law. This publication is provided as is, and is to be used at the recipient's own risk. The recipient is advised to consider seeking professional guidance with respect to its use of this publication. This publication is not intended to constitute a contract. Users are responsible for its correct application. @ The British Standards Institution 2023 Published by BSI Standards Limited 2023 ISBN978053922218 0 ICS 25.040.40 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2023. Amendments/corrigenda issued since publication Date Textaffected BS IS0 15531-42:2005 INTERNATIONAL ISO STANDARD 15531-42 First edition 2005-09-15 Industrial automation systems and integration Industrial manufacturing management data - Part 42: Time Model Systemes d'automatisation industrielle et integration - Données de gestion de fabrication industrielle - Partie 42: Modele du temps Reference number IS0 15531-42:2005(E) ISO @ ISO 2005 BSIS0 15531-42:2005 IS0 15531-42:2005(E) COPYRIGHT PROTECTED DOCUMENT IS0 2005, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 . CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 [email protected] www.iso.org ii @ IS0 2005 - All rights reserved BS IS0 15531-42:2005 IS0 15531-42:2005 Contents Page Foreword ..V Introduction ..vi 1 Scope 2 Normative references ..1 3 Terms, definitions and abbreviations 3.1 Terms and definitions. 3.2 Abbreviated terms .5 4 Overview of the whole IS0 15531 scope .5 5 Domain property. 6 5.1 Preamble .6 5.2 Fundamental concepts and assumptions 6 5.3 Domain property schema definition. .7 5.4 Domain property type definitions. 7 5.4.1 type_of_identifier_of_dom_gen_struct 1 5.4.2 type of domain. 7 5.5 domain_property subtype constraint definitions 7 5.5.1 covered_range 5.5.2 complcompos_discrcont_bounded .8 5.5.3 complete composite.. .8 5.5.4 discrete continuous. .8 5.5.5 lowerupper.. .8 5.5.6 compl_continuous_discrete 5.5.7 compos_continuous_discrete 9 5.5.8 cont_complete_composite 9 5.5.9 disc_complete_composite 5.5.10 both_bd_compl_compos_disc_cont 10 5.5.11 low_bd_compl_compos_disc_cont 10 5.5.12 up_bd_compl_compos_disc_cont. .10 5.5.13 compl_disc_low_both_up. 11 5.5.14 compl_cont_low_both_up 11 5.5.15 compos_cont_low_both_up 11 5.5.16 compos_disc_low_both_up. 11 5.6 Domain property entity definitions .12 5.6.1 domain 12 5.6.2 time_domain 12 5.6.3 domain_generic_structure. 12 5.6.4 complete_or_composite_domain 13 5.6.5 discrete_or_continuous_domain 13 5.6.6 bounded_domain. .13 5.6.7 complete_domain 13 5.6.8 composite_domain