ISO INTERNATIONAL STANDARD 15513 First edition 2000-05-01 Cranes Competency requirements for crane drivers (operators), slingers, signallers and assessors Appareils de levage a charge suspendue - Compétences requises pour les conducteurs (opérateurs), les élingueurs, les signaleurs et les controleurs Reference number ISO 15513:2000(E) ISo @ ISO 2000 ISO 15513:2000(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO2000 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic in the country of the requester. ISO copyright office Case postale 56 . CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 734 10 79 E-mail [email protected] Web www.iso.ch Printed in Switzerland @ ISO 2000 - All rights reserved ISO15513:2000(E) Contents Page Foreword. iv Introduction 1 Scope 2 Normative references 3 Terms and definitions .. 4 Assessment 4.1 General..... 4.2 Written assessment. 4.3 Oral assessment. 4.4 4.5 Reassessment 5 Competency requirements.. 5.1 General...... 5.2 Competency requirements for the crane driver (operator) 5.3 Competence requirements for the slinger ..... 5.4 Competency requirements for the signaller .. 5.5 Evidence of assessments... 16 6 Assessors, accreditation body and verification of assessment. 6.1 Assessors.. 6.2 Accreditationbody... ..18 6.3 Verification of assessment. 6.4 Requirements of assessors... 19 Annex A (informative) Assessment summary for slinger certificate. Annex B (informative) Assessment summary for jib crane operator . Annex C (informative) Assessment of crane drivers (operators), slingers and signallers on?served ii ISO 15513:2000(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (isO member bodies). The work of preparing International Standards is normally carried out through IsO technical committees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeenestablishedhas Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 3. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 15513 was prepared by Technical Committee ISO/TC 96, Cranes, Subcommittee SC 5, Use, operation and maintenance. Annexes A, B and C of this International Standard are for information only @ISO 2000 - All rights reserved IS015513:2000(E) Introduction The objective of this International Standard is to achieve uniform competency standards for work involving crane drivers (operator) slingers, signallers and their assessors. CaovriahtIntenafonaioranizationfr tandardizaionserved V Copvriaht International Oraanization for Standardizatior INTERNATIONAL STANDARD ISO 15513:2000(E) Cranes Competency requirements for crane drivers (operators): slingers, signallers and assessors Scope This International Standard gives competency requirements applicable for the se