ISO INTERNATIONAL STANDARD 15465 First edition 2004-03-15 Pipework Stripwound metal hoses and hose assemblies Tuyauteries Tuyaux et tuyauteries métalliques flexibles agrafes Reference number AY ISO 15465:2004(E) ISO @ ISO 2004 ISO 15465:2004(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The Iso Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation ? ISO2004 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either isO at the address below or IsO's member body in the country of the requester. ISO copyright office Case postale 56 . CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ ISO 2004 - All rights reserved ISO 15465:2004(E) Contents Page Foreword. iv Introductior 1 Scope. 2 Normative references 3 Termsanddefinitions 4 Information to be supplied by the purchaser.... 5 Hose types 6 Requirements 6.1 Materials.... 6.2 Hose dimensions 6.3 Tensile strength 6.4 Crush strength 6.5 Temperature 6.6 Pressure (for type DoP hose only) 6.7 Assembly 7 Typetests 7.1 Tensile strength test.... 8 7.2 Crush strength test .. 9 7.3 Bend test. 7.4 Pressure test (for type DOP hose) 11 8 Production tests Pressure proof test (for type DoP hose) .11 9 Designation 11 10 Marking. 12 Bibliography alion'ghts reserved ii ISO 15465:2004(E) Foreword ISo (the International Organization for Standardization) is a worldwide federation of national standards bodies (IsO member bodies). The work of preparing International Standards is normally carried out through IsO technicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnical committeehasbeen non-governmental, in liaison with iso, also take part in the work. Iso collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEc Directives, Part 2 The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. Iso shall not be held responsible for identifying any or all such patent rights. ISO 15465 was prepared by Technical Committee ISO/TC 5, Ferrous metal pipes and metallic fittings, Subcommittee Sc 11, Metal hoses and expansion joints. This first edition of ISO 15465 cancels and replaces ISO 7657:1995, ISO 7658:1984, ISO 8444:1985 ISO 8445:1995, ISO 8446:1995, ISO 8447:1986, ISO 8448:1986, ISO 8449:1995 and ISO 8450:1986 of which itconstitutesatechnicalrevision. @ IS0 2004 - All rights reserved ISO 15465:2004(E) Introduction It was decided to produce an International Standard under the Vienna Agreement, on technical cooperation between ISO and the European Committee for Standardization, CEN, in order to maintain one document. The opportunity was taken to replace all existing stripwound standards into this single document and to reformat it such that its layout is similar to the Internatioanl Standard for corrugated ho