ISO INTERNATIONAL STANDARD 15032 First edition 2000-04-15 Prostheses Structural testing of hip units Protheses - Essais portant sur la structure des protheses de hanche Reference number ISO 15032:2000(E) ISO @ ISO 2000 THS under Not for Resale ISO 15032:2000(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The Iso Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by isO member bodies. In the unlikely event @ISO2000 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56.CH-1211Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 734 10 79 E-mail [email protected] Web www.iso.ch Printed in Switzerland Iso2000-All rightsreserved itted without license from IHS Not for Resale ISO 15032:2000(E) Contents Page Foreword .iv Introduction. 1 Scope 2 Normative reference.. 3 Terms and definitions . 4 Test configurations 4.1 General.... 4.2 Axes of coordinate system. 4.3 4.4 Reference points.. 4.5 Test force.... 4.6 4.7 Reference distances. .5 5 Test samples .... 5.1 Types of test sample ... 5.2 Responsibilities regarding selection, preparation and alignment of test samples... 5.3 5.4 Preparation of test samples... 5.5 Alignment of test samples ... 6 Test requirements and conditions.... 6.1 Types of test.... .8 6.2 Test loading requirements... 8 6.3 Requirements and conditions relevant to test procedures and equipment.. .9 6.4 A-P and M-L test procedures.... 6.5 Torsional test procedures.... 18 6.6 Number of tests required ... 6.7 Restrictions on multiple use of test samples ... 23 6.8 23 7 Test loading parameters .. 24 7.1 Test loads and references ..... 24 7.2 Details of loading .. .25 8 Test submission document 27 8.1 Document need... 27 8.2 General requirements... .27 8.3 8.4 Information required for tests ... .28 9 Test report.. 29 9.1 General requirements.. 29 9.2 Records required for all test samples .29 9.3 Records required for all tests.... 30 9.4 Records required for results of A-P and M-L tests, .30 9.5 Recordsrequiredforresultsoftorsionaltests 31 Annex A (normative) Description of internal loads and their effects... 32 Annex B (informative) Reference data for the specification of the A-P, M-L and torsional test loading 35 Bibliography.. 38 ili se from IHS Not for Resale ISO 15032:2000(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (isO committees. Each member body interested in a subject for which a technical committee has been established has liaison with IsO, also take part in the work. IsO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. patent rights. IsO shall not be held responsible for identifying any or all such patent rights International Standard ISO 15032 was prepared by Technical Committee ISO/TC 168, Prosthetics and orthotics. Annex A forms an integral part of this International Standard. Annex B is given for information only ional Organization for Standardization ISO 2000 - All rights reserved ISO 15032:2000(E) Introduction Throughout this