ISO NTERNATIONAL STANDARD 14952-5 First edition 2003-11-15 Space systems Surface cleanliness of fluid systems - Part 5: Drying processes Systemes spatiaux - Proprete des surfaces en contact avec des fluides Partie 5: Procédés de séchage Reference number ISO 14952-5:2003(E) ISO @ISO2003 E"eqr[tkijvgf"d["WPG.'E1"1gpqxc."8I"4:226"Ocftkf.'Urckp"*cm'tkijv Ygf"Hgd’36*27239.6:"WVE"4246 knnutravintiInfl ISO 14952-5:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The Iso Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below @ISO2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, Iso's member body in the country of the requester. ISO copyright office Case postale 56: CH-1211 Geneva 20 Tel.+ 4122 749 0111 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ii E"eqr[tkijvgf"d["WPG.'E1"1gpqxc."8I"4:226"Ocftkf.'Urckp*cm'tkijvu'tgugtxgf+*"Ygf"Hgd’36*27<39<6:"WVE"4246 @Iso2003—Allrightsreserved knnitrawintiInfi ISO 14952-5:2003(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (isO member bodies). The work of preparing International Standards is normally carried out through IsO technicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnical committeehasbeer non-governmental, in liaison with IsO, also take part in the work. IsoO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2 The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote ISO 14952-5 was prepared by Technical Committee ISO/TC 20, Aircraft and space vehicles, Subcommittee Sc 14, Space systems and operations. Iso 14952 consists of the following parts, under the general title Space systems - Surface cleanliness of fluid systems: — Part 1: Vocabulary 一Part2:Cleanlinesslevels Part 3: Analytical procedures for the determination of nonvolatile residues and particulate contamination Part 4: Rough-cleaning processes Part 5: Drying processes Part 6:Precision-cleaning processes ili ISO 14952-5:2003(E) Introduction This part of IsO 14952 describes a method for vacuum drying intricate parts or components that are likely to retain entrapped moisture when dried by normal purging techniques. The purpose of this part of isO 14952 is to provide processes that can be used to ensure the dryness of parts or components subjected to solvent- based or water-based cleaning processes. iv @ ISO 2003 - All rights reserved E"eqr[tkijvgf"d["WPG.'E1"1gpqxc."8I"4:226"Ocftkf.'Urckp*cm'tkijvu'tgugtxgf+*"Ygf"Hgd’36*27<39<6:"WVE"4246 fwoknnit'ravintiInfl ISO 14952-5:2003(E) INTERNATIONAL STANDARD Space systems Surface cleanliness of fluid systems - Part 5: Drying processes 1 Scope This part of isO 14952 provide