ENIEC63489 EUROPEANSTANDARD NORMEEUROPEENNE EUROPAISCHENORM September 2025 ICS25.040.40;01.110 English Version Common data concepts for smart manufacturing (IEC63489:2025) Concepts de donnees communs pour la fabrication GemeinsameDatenkonzeptefurSmartManufacturing intelligente (IEC 63489:2025) (IEC 63489:2025) This European Standard was approved by CENELEC on 2025-08-20. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre orto any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic. Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkiye and the United Kingdom. CENELEC EuropeanCommitteeforElectrotechnical Standardization ComitéEuropéendeNormalisationElectrotechnique Europaisches Komitee fuir Elektrotechnische Normung CEN-CENELEC Management Centre:RuedelaScience23,B-1040 Brussels Ref.No.EN IEC 63489:2025 E EN IEC63489:2025 (E) European foreword The text of document 65E/1084/CDV, future edition1 of IEC 63489,prepared by SC 65E"Devices and automation"was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as ENIEC63489:2025. The following dates are fixed: 2026-09-30 latest date by which the national standards conflictingwiththe(dow)2028-09-30 document have to be withdrawn Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights. Any feedback and questions on this document should be directed to the users'national committee. A complete listing of thesebodies can be found on the CENELEC website. Endorsement notice The text of the International Standard IEC 63489:2025 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standard indicated: IEC61360-7NOTEApprovedasENIEC61360-71 IEC61987-100NOTEApprovedasENIEC61987-100 1Under preparation. Stage at the time of publication: prEN IEC 61360-7:2025 2 ENIEC 63489:2025 (E) Annex ZA (normative) Normativereferencesto international publications withtheircorrespondingEuropeanpublications The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. relevant EN/HD applies. NOTE2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cencenelec.eu. Publication Year Title EN/HD IEC 61360 IECCommonDataDictionary 3 JEC IEC 63489 Edition 1.0 2025-07 INTERNATIONAL STANDARD Common data concepts for smart manufacturing IEC 63489:2025-07(en) ICS 25.040.40; 01.110 ISBN 978-2-8327-0561-2 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright @2025 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm,