ETSI EN 300 220-1 V2.4.1 (2012-05) ETSI European Standa rd Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment to be used in the 25 MHz to 1 000 MHz frequency range with power levels ranging up to 500 mw; Part 1: Technical characteristics and test methods ETSI EN 300 220-1 V2.4.1 (2012-05) 2 Reference REN/ERM-TG28-434 Keywords radio, SRD, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.:+33492944200Fax:+33493654716 Siret N°348 623 562 00017 - NAF 742 C Association a but non lucratif enregistree a la Sous-Préfecture de Grasse (06) N°7803/88 Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive withinETSISecretariat. Usersof thepresentdocument shouldbeawarethatthedocumentmaybesubjectto revisionorchangeof status Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. @ European Telecommunications Standards Institute 2012. All rights reserved. 3GPpTM and LTETM are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM@ and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 300 220-1 V2.4.1 (2012-05) 3 Contents Intellectual Property Rights.. Foreword. Introduction 1 Scope References.. Normative references 10 2.2 10 3 Definitions, symbols and abbreviations 11 3.1 Definitions. 11 3.2 Symbols........ 3.3 Abbreviations.. 4 Technical requirement specifications... 4.1 General requirements ........ 4.1.1 Receiver category 14 4.1.2 Generalperformancecriteria. 4.2 Presentation of equipment for testing purposes.... 4.2.1 Choice of model for testing .. 4.2.2 Testing of equipment with alternative power levels .... .16 4.2.3 Testing of equipment that does not have an external 50 2 RF connector (integral antenna equipment) ... 4.2.3.1 Equipment with an internal permanent or temporary antenna connector or using a dedicated test fixture... 4.2.3.2 Equipment with a temporary antenna connector ... 4.3 Mechanical and electrical design... 4.3.1 General..... 4.3.2 16 4.3.3 Transmitter shut-off facility... 4.3.4 Receiver mute or squelch.... 4.3.5 Marking (equipment identification).... 4.4 Auxiliary test equipment... 5 Test conditions, power sources and ambient temperatures .... 5.1 Normal and extreme test conditions .. 5.2 Test power source........ 5.2.1 External test power source...... 5.2.2 Internal test power source ... 5.3 Normal test conditions... 8 5.3.1 Normal temperature and humidity ... 18 5.3.2 Normal test power source ... 18 5.3.2.1 Mains voltage.. 18 5.3.2.2 Regulated lead-acid battery power sources . 18 5.3.2.3 Other power sources... 5.4 Extreme test conditions .. 5.4.1 Extreme temperatures ... 5.4.1.1 Procedurefortests atextremetemperatures.. 18 5.4.1.1.1 Procedure for equipment designed for continuous operation ... 19 5.4.1.1.2 Procedure for equipment designed for intermittent operation .. 5.4.1.2 Extreme temperature ranges. 5.4.2 Extreme test source voltages.... 19 5.4.2.1 Mains voltage. 19 5.4.2.2 Regulated lead-acid battery power sources 20 5.4.2.3 Power sources using other types of batteries... 20 5.4.2.4 ETSI EN 300 220-1 V2.4.1 (2012-05) 4 6 General conditions... .20