IEC IEC 62150-6 Edition 1.02022-01 INTERNATIONAL STANDARD NORME INTERNATIONALE colour nside Fibre optic active components and devices - Test and measurement procedures - Part 6: Universal mezzanine boards for test and measurement of photonic devices Composants et dispositifs actifs fibroniques - Procedures d'essais et de mesures- Partie 6: Cartes mezzanines universelles pour les essais et les mesures des dispositifs photoniques IEC 62150-6:2022-01(en-fr) IEC IEC62150-6 Edition 1.02022-01 INTERNATIONAL STANDARD NORME INTERNATIONALE colour nside Fibre optic active components and devices - Test and measurement procedures - Part 6: Universal mezzanine boards for test and measurement of photonic devices Composants et dispositifs actifs fibroniques - Procédures d'essais et de mesures Partie 6: Cartes mezzanines universelles pour les essais et les mesures des dispositifs photoniques INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE ICS 33.180.20 ISBN 978-2-8322-0112-1 Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agree. ? Registered trademarkofthe Interr onalElectrotechnical Commission Marque deposee de la Commission Electrotechnique Internationale - 2 IEC62150-6:2022@IEC2022 CONTENTS FOREWORD. INTRODUCTION. Scope. 1 2 Normative references . 3 Terms and definitions . 4 Mezzanine board requirements. 4.1 Functional description ... 4.2 Critical dimensions.. 4.3 Daughtercard and extended system.. 11 4.4 Power and signal flows ... Annex A (informative) International collaborative research and development. A.1 Overview. .18 A.2 European FP7 PhoxTroT project ... A.3 European H2020 Nephele project ... A.4 European H2020 COsMICC project ... ..19 A.5 Benefit of universal test board.. .20 Bibliography... Figure 1 - Outlines of mezzanine test boards . Figure 2 - Attachment of PDS onto M2 board .. Figure 3 - Mezzanine board 1 (M1) - Relative positions of power and low speed signal connectors on top and bottom surfaces and mezzanine board origin...... ........... Figure 4 - Mezzanine board 2 (M2) - Relative positions of power and low speed signal connectors on top and bottom surfaces and mezzanine board origin...... Figure 5 - Power distribution and sensor board (PDS) - Relative positions of power and low speed signal connectors on bottom surfaces and mezzanine board origin.......... 10 Figure 6 - Outline dimensions of extended double Eurocard form factor daughtercard with electrical edge connectors and cut-outs to accommodate optical backplane connectors.... Figure 7 - Attachment of M2 boards onto daughtercard ... ..13 Figure 8 - Extended double Eurocard form factor daughtercard with two M2 boards attached........ ..14 Figure 9 - Extended double Eurocard form factor daughtercard with four M1 boards attached........ Figure 10 - Extended double Eurocard form factor daughtercard with two M1 boards and one M2 board attached ............... Figure 11 - Functional diagram showing power and low speed signal distribution between PDS, M1/M2, daughtercard and backplane ....... ...16 Figure 12 - Multiple daughtercards populated with M1/M2 and PDs in multiple slots on a system backplane ..... ..17 Figure A.1 - Example of cross-project deployment of mezzanine test card [3].. .....18 Figure A.2 - Examples of M2 test boards developed on EU H2020 COsMICC project.......20 Table 1 - Critical relative dimensions. .11 Table 2 - Voltages and low-power signal designations. ..16