EN IEC 62382 EUROPEANSTANDARD NORMEEUROPEENNE EUROPAISCHE NORM September 2024 Supersedes EN 62382:2013 ICS25.040.40 English Version Control systems in the process industry - Electrical and instrumentation loop check (IEC 62382:2024) Systemes de commande dans I'industrie de transformation Leittechnische Systeme in der verfahrenstechnischen Industrie - PLT-Stellenprufung Controle de boucle des circuits électriques etdes appareillages (IEC 62382:2024) (IEC62382:2024) This European Standard was approved by CENELEC on 2024-09-18. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management CentreortoanyCENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway,Poland, Portugal, Republic of North Macedonia, Romania, Serbia,Slovakia, Slovenia,Spain,Sweden, Switzerland, Turkiye and the United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comite Europeen de Normalisation Electrotechnique Europaisches Komitee fur Elektrotechnische Normung CEN-CENELECManagementCentre:RuedelaScience23,B-1040Brussels @ 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref.No.ENIEC62382:2024E EN IEC 62382:2024 (E) European foreword The text of document 65E/1082/FDIS, future edition 3 of IEC 62382, prepared by SC 65E "Devices automation" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as ENIEC62382:2024 The following dates are fixed: latest date by which the document has to be implemented at national (dop) 2025-06-18 latest date by which the national standards conflicting with the (dow) 2027-09-18 document have to be withdrawn This document supersedes EN 62382:2013 and all of its amendments and corrigenda (if any) Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights. completelistingofthesebodiescanbefoundontheCENELECwebsite. Endorsement notice The text of the International Standard IEC 62382:2024 was approved by CENELEC as a European Standard without any modification. IEC 61131 (series) NOTE Approved as EN IEC 61131 (series) IEC 61511 (series) NOTE Approved as EN 61511 (series) IEC 61511-1:2016 NOTE Approved as EN 61511-1:2017 (not modified) IEC 62443 (series) NOTE Approved as EN IEC 62443 (series) IEC 62708 NOTE Approved as EN 62708 2 EN IEC 62382:2024 (E) Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. here: www.cencenelec.eu Publication Year Title EN/HD Year EN IEC 62381 IEC 62381 Automation systems in the process - industry - Factory acceptance test (FAT), site acceptance test (SAT), and site integrat